Skip to main navigation Skip to main content Skip to page footer

01

Selection criteria

How do you choose a suitable polyimide film tape?

Compare each product's construction: polyimide backing, adhesive type, thickness and supplied width. For masking during soldering, also consider the temperature profile, exposure time and removal afterwards. The term “polyimide film” alone tells you nothing about whether the adhesive layer and the complete application will be suitable.

02

POLYIMIDE RANGE

Polyimide film tapes for technical masking

The listing shows products assigned to the polyimide category, including single-sided film tapes with a polyimide backing in different versions. Check the construction and application details on each product page.

2 products found

RK 935 Polyimide Film

adhesive tape

RK 935 Polyimide Film

2 versions

Krückemeyer RK 935 polyimide film – 640 mm x 33 m, heat-resistant up to +260 °C, silicone adhesive…

Price on request View details

No products match this combination.

No products match all of the selected filter criteria.

The products could not be loaded. Please try again later.
No products match all of the selected filter criteria. The products could not be loaded. Please try again later. Load more products Loading products... Remove all

03

CONSTRUCTION AND PROCESSING

Relating a Kapton search to the polyimide range

Kapton is a name for polyimide film; the listing groups products under the polyimide material category. The material name alone tells you neither the brand nor the properties of the finished tape. According to its technical data sheet, RK 935, for example, has a polyimide film coated on one side with silicone adhesive. Its temperature specification concerns short-term exposure for that particular product; it does not approve other polyimide tapes or your entire process.

If you mask circuit boards or other components, tell us the substrate, temperature profile, exposure time and required removal method. For the supplied format, add the roll width, geometry and processing steps. Krückemeyer GmbH can assess suitable base material with you and whether slit rolls or die-cut parts will support handling in your production. For a broader material choice, see polyimide film; for other plastic films, see plastic film.

04

QUESTIONS ABOUT KAPTON AND POLYIMIDE

Is every polyimide film in the listing a Kapton film?

No. The listing uses the polyimide material category; it does not tell you which film brand an individual product contains. Kapton denotes a polyimide film, whereas some listed products are complete film tapes with a backing and adhesive layer. Check the brand, exact construction and details of each product if your specification requires Kapton film. State that requirement explicitly in your enquiry so the category name alone is not used to select a product.

What determines suitability for a soldering process?

The specification for the particular tape and the actual temperature profile of your process are decisive. The data sheet for RK 935 describes a polyimide backing with silicone adhesive and expressly identifies its temperature resistance as short-term. This does not establish the same resistance for all polyimide tapes at the same exposure time. State the temperature reached, its duration, the substrate and the intended removal method. Then test suitability on the intended component in the intended process.

Which details matter for electrical insulation with a polyimide tape?

For electrical insulation, consider the values for the specific product and the conditions of your application. The technical data sheet for RK 935 gives an insulation class and a dielectric breakdown value. Those figures concern that product under the conditions of its data sheet; they are not a general approval for every polyimide tape or a finished assembly. Tell us the electrical requirement, material construction and conditions of use so the relevant product data can be checked.

How can polyimide film tape be converted for processing?

Krückemeyer GmbH can slit suitable base material to size or convert it into die-cut parts for the application. The useful format depends on component geometry, the masking area and the steps used to apply and remove it. Converting does not automatically change the properties of the base material or adhesive. In your enquiry, specify the material requirement, desired width or outline, and processing step. Product choice and supply format can then be assessed together.

05

Request advice

Describe your component, surface, temperature profile and the masking or insulation you need. We will review the specific film construction and a suitable converted supply format with you.

Discuss polyimide film for your application

Material construction, process conditions and geometry determine the right choice. Contact us about your requirements or send specific products through the enquiry list.

Thomas Klein

ADVICE ON POLYIMIDE FILMS

Thomas Klein

Contact for products

Thomas Klein will discuss film construction, conditions of use and the appropriate supply format with you.